 |
 |
 |
 |
 |
| |
| Techenical Data & Specifications for standard model KAG-0, 1, 2, 3, 4, 5, 6, 7, 8 |
| |
STD C. H. |
12" C. H. |
| Centre Height over flat bed ways |
267 mm |
305mm |
| Swing Over Bed |
525 mm |
600mm |
| Swing Over Cross Slide |
300mm |
375mm |
| Swing In Gap |
830mm |
910mm |
| Length of Gap in front of Face Plate |
200mm |
200mm |
| Width of Bed: • Standard 325mm (13") • Optional:375mm(15") |
|
| |
| MODEL |
Admit Between
Centers |
Length of Bed |
Floor Space
Occupied (mm) |
Approx Weight in kgs. |
| Nett. |
Gross |
| KAG - 0 |
525 mm |
1675 mm (5'-6") |
2200 x 1450 |
1450 |
1750 |
| KAG - 1 |
1000 mm |
2135 mm (7') |
2660 x 1450 |
1500 |
1900 |
| KAG - 2 |
1600 mm |
2745 mm (9') |
3140 x 1450 |
1650 |
2150 |
| KAG - 3 |
1900 mm |
3050 mm (10') |
3500 x 1450 |
1900 |
2450 |
| KAG - 4 |
2500 mm |
3660 mm (12') |
4110 x 1450 |
2050 |
2650 |
| KAG - 5 |
3100 mm |
4270 mm (14') |
4720 x 1450 |
2350 |
2950 |
| KAG - 6 |
3710 mm |
4875 mm (16') |
5330 x 1450 |
2700 |
3400 |
| KAG - 7 |
4320 mm |
5485 mm (18') |
5940 x 1450 |
3000 |
3800 |
| KAG - 8 |
4930 mm |
6095 mm (20') |
6550 x 1450 |
3300 |
4200 |
| Main Spindle: Spindle bore 51mm |
|
| Type of Spindle Nose |
A 2 - 6 |
Standard Accessories:
Flame Hardened bed ways, Chuck back plate 1 no, centre adapter, Dead centres (MT - 4) 2 nos, Tool Post Spanner, Motor pully, Thread dial indicator, Change gear set - 1 (For metric and inch both) and Norton gearbox. |
| Spindle Morse Tapper |
MT - 6 |
| Spindle Adapter Morse Tapper |
MT - 4 |
| Spindle Speeds Nos. / RPM / Range |
12 |
30, 43, 55, 85, 115, 160, RPM |
| 210, 285, 400, 545, 785, 1060 RPM |
| Spindle Mounting on |
Tapper Roller Bearings |
| Tail Stock Spindle: Diameter: 60.3mm / Travel: 180mm / Morse Tapper: MT - 4 |
|
| THREADS |
|
Optional Accessories:
Face plate, Carrier plate, steady rest, follow rest, Tapper turning attachment, motorised coolant pump with tank and fittings, Rear tool post with extended cross slide, Chuck back plate (Extra), and Electricals (Motor, Panel board, Wirings, Push button Switches, V-belts and fittings), Electricals Switch shaft and chip guard. |
Nos. of Threads / Range
for Fully norton Gearbox |
Metric :
Inch : |
17 / 0.5 mm To 15 mm Pitch
40 / 2 to 60 TPI |
| FEEDS |
|
Nos. of Feeds / Range
for Fully norton Gearbox |
Longitudinal :
Cross : |
40 / 0.066 to 2 mm / rev. of spindle
40 / 0.0165 to 0.5 mm / rev of spindle |
|
|
Electricals: Electrical motor of 3 HP / 2.25 k.w., 3 Phase, 1440 RPM
(Panel board wirings, over load relay, Pushbutton switches, V-belts and fittings - Optional) |
| |
|
|
|
|
